new to emu

[budwiseradam]

hi im going to try my luck at emu but dont know where to start ,done lots of reading on top ond think i have a understanding of it but cant flash my 2313 ,its in my unmodded t911 and cant remeber how to flash ,if anyone has the time to help would be appreciated

[budwiseradam]

ok got it to flash now i need to know the newest flash for 2313 and bev.and what numbers to use with my ird 3100

[JT]

Do you have a one, two or three chip emu board? Flash depends on the board a little bit. Is the board internal or external?

[agarnet]

The newest flash for 2313 bev is Rev 248 (See the file download section). Find the one appropriate to your setup: it will depend on if you have a Max232 chip on your emulator board.

Public IRD numbers
BEV: IRD# R 00 4502 4458-77 (02AF04CA) and Boxkeys FD BF 2E 56 AF FA 72 64
DISH: IRD # R0018642028 (011C746C) and Boxkeys 8C A6 A8 8C FD E2 E2 63

[josmed]

The newest flash for 2313 bev is Rev 248 (See the file download section). Find the one appropriate to your setup: it will depend on if you have a Max232 chip on your emulator board. Public IRD numbers
BEV: IRD# R 00 4502 4458-77 (02AF04CA) and Boxkeys FD BF 2E 56 AF FA 72 64
DISH: IRD # R0018642028 (011C746C) and Boxkeys 8C A6 A8 8C FD E2 E2 63

Is the old Max and Mel good to use now or do I have to buy a new Max and Mel board?

TIA

[budwiseradam]

hi thanks for fast reply im just trying the 1chip
2313 and want to run bell

[budwiseradam]

well its a no go i just kept getting card not inserted correctly is there something more to do or just download selfextrator floppy boot disk?
and boot from floppy

[SuperManny]

Is the old Max and Mel good to use now or do I have to buy a new Max and Mel board?
TIAThe old one works, but you need to reflash it with a current rev flash.

[josmed]

The old one works, but you need to reflash it with a current rev flash.

Thanks SuperManny, which flash is that?

TIA

[budwiseradam]

can someone help me edit my time i finly got eveything working but 3 hours behind and dont know how to edit my timezone im useing BELL ST19 CEMU.exeand have all chanels but like i said 3 hours behind on ird

[SuperManny]

Thanks SuperManny, which flash is that?

TIAThere are multiple flashes out there that work, because they're pretty easy to make. You just need to find the right type.

There are 3 main types, The Single Chip, mostly used for AVRs and flashed with jEEpers, the 2-chip for all standard Max-Mel 2313 emus, and the AT-Tiny for use with the Mountain Man programmer.

[JT]

The attiny chip can be programed with the same programmer as the atmel chip using AVReal software. There is also a three chip max/mel board.

To edit your time you will have to go into the 18k st19 file the boot disk creator built for you. It's a rom102 eprom file or .bn102 file that's been renamed, so rename it something with the .bin102 extention and you can open it up with most programs. I don't know where Bell keeps their time zone byte though, or what byte codes for what time zone. You'll have to find that with a search.

[josmed]

There are multiple flashes out there that work, because they're pretty easy to make. You just need to find the right type.

used for AVRs and flashed with jEEpers, the 2-chip for all standard Max-Mel 2313 emus,

what flash is used for the Max&Mel? I've been all over and have not found anything

[JT]

10bar.hex for Dish

[josmed]

10bar.hex for Dish

Got it, which program to load this to the Max&Mel?

[SuperManny]

Check out Smiling Jack's how-to here
http://www.dssftp.com/forum/showthread.php?t=68787