I am unable to unlock my card

[razi]

I have used this same card over and over. It is 102 rev 103 card and it was unlocked. I just wrote aio bin on it and it became rev 10c. I know i have put the password on it whic I use over and over. When I try to unlock it with my password, it did not unlock. Also I am seeing unknown provider now. The ATR is valid and also rom 102 rev10c I can see but unlock unsucessful. Please help.

[joesnuffy]

I loaded one yesterday and did the same thing. I think the 10C locks you out. Once loaded the card showed 10C. I placed the card in receiver for like 2 hours pulled it and tried to read and it had become 103 rev. My card did show provider like it should. I then tried to unlock it using a script for that rev FFF;d it up. Now I wish I would have just left it in the rec it most likely would have updated to 10C rev and worked. Maybe I should have used the 10B script. I hope that helps.

Joe

[razi]

I had several time 10 C blocker written on this card. It has original rev 103 image. I know I have put the password on it. I have done it 100's of times in the past with no problem and sucessfully get back in it after providing the password. But this time I can't get in. Also i am seeing "UNKNOWN provider". It says, cam : Rom 102 Rev 10C. I think it is a pice of garbage now or someone can share with me his experience how to make it useful again.

[razi]

One more thing to add here. This time I added the patches through Nagramaster 4.1 (which usually I never do, I always write patches using N2Edit 2.58). So what I did different this time that I applied patches using Nagramaster 4.1 and saved the image. Then I opened the image in N2Edit and applied the final patch ( changed the password to my liking) and then I applied that patch and also check it that the patch my given password was there. I then put that card in the ird. After 10 minutes I took out and then tried to open it and at that time it failed. This is the exact story if someone interested.

[joesnuffy]

You might try leaving it in the ird longer. I would leave it in all night and see if that helps before trying a script on it. Also go back to where you saved the file if you did and check for the password. Try 8383838383838383 try 0000000000000000 try deadbeefbaadf00d try what it use to be also maybe you didn't change it just thought you did. Its been my experience when you see unknow provider you most likely have other issues. I also read somewhere that if it is and actual sproof to 10C a 103 unlocker script might get you in. Use high ohms on the pot like 225ohms.

Joe

[dino-]

I have a card same way unknown provider. and locked out, error at line 3080
I also tried applying patches in nagramaster 4.1 when I should have been using n2edit and I believe this is the problem
I have tried all kinds of d2c and every password mentioned as well as more with no luck my next step is to have a friend try to reglitch it
this card has never been back in ird since this error at 3080
what should be done first with a card like this try reglitch first or put in ird and see what happens(don't want a stream locked 10c)

[BigPappi]

I am using a 102 card with spoofed to 10C, All channels are fine but should I pull it, I do not want this to happen to my card... pLease let me know

[razi]

I have a card same way unknown provider. and locked out, error at line 3080
I also tried applying patches in nagramaster 4.1 when I should have been using n2edit and I believe this is the problem
I have tried all kinds of d2c and every password mentioned as well as more with no luck my next step is to have a friend try to reglitch it
this card has never been back in ird since this error at 3080
what should be done first with a card like this try reglitch first or put in ird and see what happens(don't want a stream locked 10c)

Exactly this is my case. I am also seeing error at line 3080. Let me know if you able to glitch this card.

[satnutzz]

The cards are only spoofed to 10c-so yes,use a rev 103 script-loader2 settings.
They should pop quickly.

Once it pops-write a virgin rev 103 image to it & you should be good to go.

Good-luck!

[mightymouse]

I too have this problem. When trying to glitch using rev103 unlocker, I get Bad CMD04 response.....

[joesnuffy]

"I am using a 102 card with spoofed to 10C, All channels are fine but should I pull it, I do not want this to happen to my card... pLease let me know" You loaded your card correctly these other folks did not. You should be ok unless they comprimise your blocker.


Joe

[Nookiedawg]

I too have this problem. When trying to glitch using rev103 unlocker, I get Bad CMD04 response.....
I got the exact same response.. have tried rebelsurf to restore cmd04 and or fix unknown provider, all the passwords etc.. All 102rev103 scripts give bad cmd04 response.. trying for days and nothing is working. Has anyone had any luck unlocking these cards?

Patched using Nagra Edit 5.2 and written using n2edit 2.58

tried unlocking using orange nexus 4053 chipset

[joesnuffy]

What scripts are you running? What is your ohms on your pot set to, how much voltage are you using? What loader are you using? givie us some facts. Try increasing your ohms on pot.

Joe