10B Unlocking

[joesnuffy]

I wonder how many folks have 10 Bs they need unlocked especially right now. I can get in them easily as long as their actual cards.. If someone needs help drop me a pm.

Joe

[TVtester]

Sent you a PM...

TVtester

[chess1939]

Sent you a PM

Chess1939

[joesnuffy]

I have had numerous pms. Most of which want to know my settings, script, etc. I will be more than happy to share that with you guys. Here they are use them at your own risk. Make sure to read the how to that is attached script. I read it and my pot settings varied dramatically to get the right readings as described in their how to. Here they are use them at your own risk and if you don't have a white nexus I do and will be glad to give it a shot not lossing but 1 out of 10.

Here is the deal. Got my white nexus from Mili.

White Nexus script (White Nexus 102_Rev_10B) thats what its called and can be obtained at the file shop.

Settings

* Dip 4 on while running script
* No diode mod or disconnected at one end
* 225-211 ohms (in his directions he was using 20 ohms I got bad responses immediately so I increased them. Start high
* NDRS flash I think is how its spelled what it asks for it will tell you what flash to use.
* Up to 1.5 hours to open card
* 9 volts dc
* no mods to script

Good Luck

Joe

[joesnuffy]

I have had numerous pms. Most of which want to know my settings, script, etc. I will be more than happy to share that with you guys. Here they are use them at your own risk. Make sure to read the how to that is attached script. I read it and my pot settings varied dramatically to get the right readings as described in their how to. Here they are use them at your own risk and if you don't have a white nexus I do and will be glad to give it a shot not lossing but 1 out of 10.

Here is the deal. Got my white nexus from Mili.

White Nexus script thats what its called and can be obtained at the file shop.

Settings

* Dip 4 on while running script
* No diode mod or disconnected at one end
* 225-211 ohms (in his directions he was using 20 ohms I got bad responses immediately so I increased them. Start high
* NDRS flash I think is how its spelled what it asks for it will tell you what flash to use.
* Up to 1.5 hours to open card
* 9 volts dc
* no mods to script

Good Luck

Joe

[joesnuffy]

Popping them like crazy send me a pm if you need assistance.

Joe

[duff]

To be fair though DVD, he is being helpful. At least he is posting his settings and script he is using. I keep getting PMs wanting $25/card with no help on the scripts or settings.

So I agree that perhaps he should say "warning, this works for me, etc" but at least he is posting his stuff for others to use instead of just trying to get people to send cards to him for cash.


<btw, I am NOT saying you are PMing for cash, but just that he is NOT doing this...I just re-read my post and wanted to be clear because you HAVE helped me in past threads. I just don't want you to take what I said the wrong way!>

[joesnuffy]

Duff,

If you look above you will see my settings I did share them. As for the rest it is a art. I see you only have a few posts I have been around here since 2002 but the server come under attack some poor old man lost his income and I had to re-register I am no newbie to this site. As for 25 dollars to make a worthless card valuable and help pay for equipment and mistakes thats everybodys call.


DVD I have been dealing with Mauisun for years. Like you said dvd not all loaders and settings are created equal. To many variables. I am not loosing 10b cards popped 2 today no losses. I even have a 1000 dollar power supply and I know how to use it the cost really doesn't matter but it works and helps reduce ice-scrappers. As for when its up to 100 well I never said it was not. I was just trying to help some folks especially right now when I know they need cards. As for Mauisun I know him and have done buiz with him for years and have already sent him my stuff but thanks for your concerns. As for taking advantage of newbies I have never done that either some folks are sending them I will let them speak for me if they like. I am sure they will if I don't take care of them. As for I haven't lost cams I can cover a christmas tree with rom2 up but I can honestly say no 10bs. If you need more proof send me one I'll pop it free make sure its one of your harder ones.

You shouldn't be so quick to judge me I have been here for years and not screwed any one. You don't know my experience when it comes to cards. I know your a decent guy from reading some of your posts maybe you should read some of mine.

Go back and look at forums and see how many people I have helped.

Not flaming just my 2 cents.

Joe

[joesnuffy]

DVD, cool. No hard feelings and Merry Christmas to you.

I am not trying to steal your thunder. I had gotten out of cards and went to cemu after last dec I can build a 2 chip max for about 10 bucks. The only reason I even re entered them is because my peeps need them. That being said the 10bs are cheap. I recently contacted Mauisun and he told me that he wasn't doing 10bs then. He might be now but I decided to try them myself and researched and discovered that script. I have altered the settings I am using. My white nexus came from mili but it is like a generic (t911 looking, mods on board, 4911 chips not the 4053s) one I have never seen one like it you put all the dip switches on but 1 to flash it then turn them all off and choose the one you want. I have also epoxied excellent pots into it with switches and they are tweaked for 10bs. I don't get in them in seconds maybe thats why I am not loosing any. Takes 1 hour up to 3 hours I had one take 3 hours the other day but it popped open. Anyway looks like your popping them for peeps here thats great I was just trying to helps some peeps out here.

Joe

[dishdude666]

Both you guys have great stats. I am expecting my T911 and a 10b next week.
I how I can depend on you guys for help.

Thank you in advance.

[joesnuffy]

Dish Dude, 10bs are the hardest card to pop not the best to learn with. What chip set is in the t911 you purchased 4053s or 4911s? That would be my first question. My loader is a modded t911 in a white case with 4911s it was suppose to be a white nexus hell it might be but its the best loader I have ever owned. Got a t911 with 4053s for lower revs. Is yours modded? If these questions aren't ringing a bell you might want to pm one of us. You can figure a 10b is worth about 70 bucks closed 150 open if its dead its worth zilch. If your going to try and pop them I will help you but expect to loose a few I wasn't kidding when I said I had enough to decorate a tree if your cool with that rock and roll.




Joe




Someone was wanting winex script here it is. I am putting the read me in the next post

''************************************************ **************************************
''WHITE NEXUS WITH 4619
'*******NOTES************************************* *********
'THIS IS WHAT HAS UNLOCKED OVER 70% OF MY 10B CARDS OUT OF
'10 I LOOPED 3 WATCH FOR THOSE 07+FF RESPONCES DONT LET IT 'HAPPEN TO MUCH. IF YOU KEEP GETTING THEM THEN TURN POT UP 'SLOWLY SO THEY GO AWAY THEN YOU SLOWLY LOWER YOUR POT TILL 'YOU GET A 07+FF RESPONCE NOW YOU KNOW HOW LOW TO GO--ADD .5 'TO THE OHM READING THIS IS NOW YOUR LOW SETTING AND LEAVE 'IT THERE AS LONG AS THERE IS NO 07+FF RESPONCES. THE KEY IS 'IF YOUR GETTING THE 07+FF RESPONCES SLOWLY GO UP ON THE POT 'AND I MEAN SLOW BY .1 IF YOU HAVE A STEADY HAND I HAVE A 'KICKASS POT SO I CAN DO IT BUT DONT BE STUPIED AND GO UP '1.0 OHMS AT A TIME YOU WILL LOOP IT THAT WAY.
'BUT IF YOU GET JUST 1 GOOD RESPONCE DONT MOVE YOUR POT JUST 'LET IT RUN IT TAKE AROUND 2HOURS TO UNLOCK.
'************************************************* **********
'FLASH = NEWDRS
'Dip 4 DOWN
'9volt 800ma
'POT:15.5 TO 21.0 OHMS DONT GO UNDER 15.0 OHMS YOU WILL
'GET TO MANY 07+FF RESONCES AND FROM MY EXPERANCE THE 07+FF 'WILL LEAD TO A LOOP SO JUST DONT DO IT. TO SET YOU POT USE 'A MULTIL MEATER SET OHMS TO 200 READING THEN SET YOUR POT 'JUST MAKE SHURE THAT WHEN YOU SET YOUR POT THE LOADER IT 'SLEF IS UNPLUGED OR HAS NO POWER
'Notes:this script takes time be paient it can take 45mins
'or so to get a +RST just let it run but if there 07+FF 'thats a bad thing move pot up then back slowly till there 'gone one a while is ok but none is better.
'THESE ARE GOOD RESPONCES IT WILL TAKE AWHILE TO GET A GOOD
'RESPONCE AND YOU MIGHT ONLY SEE 1 GOOD RESPONCE PERPAGE OF 'RUNNING SO IF YOU WATCH THE SCREEN AND YOU DONT SEE ANY 'GOOD RESPONCES WAIT AND WATCH CLOSELY THEY WILL POP UP. I 'ONCE WAITED FOR 45MINS TO GET A GOOD RESPONCE BUT IF YOU 'GET JUST 1 GOOD RESPONCE DONT MOVE YOUR POT JUST LET IT RUN 'IT TAKE AROUND 2HOURS TO UNLOCK.
'**GOOD RESPONCES FROM MY WHITE NEXUS UNLOCKER**************
'THIS IS THE FRIST GOOD RESPONCE AFTER 40+MINS OF RUNNING
'07Rst02-------07+80---------07Rst107Rst05----
'
'THEN THESE CAME LATER BUT NOT IN A ROW THIS IS 1 GOOD
'RESPONCE PER SCREEN SO THERE WHERE LOTS OF-----07RST02--- 'GOING ACRRSS THE SCRREN.
'
'07+4A
'07+52
'07+A0
'
'HOPE THIS HELPS SMART_TOYS
'Elapsed = 01:14:34
'
'--------------------------------07Rst03---------07Rst02----'------07Rst02-----------------------------------07R'st0E----'-----------------------------07Rst0C----------07Rst0C-----0'7+55 !!!!!!!
'TX Data : A1
'******* Good response received! *********
' 55
'===========================================
' 55 was hit at: Delay:140F VCC:0C GlitchType:BA/07
' Elapsed: 01:14:50
' VCC Resolution: 0.0625
' Delay Range: 140B to 1453
'********************************
'* REV 109+/247+ CAM NOW OPEN!! *
'* PROCEED AS NORMAL *
'* GOOD LUCK! :-) *
'********************************
'*
'************************************************* *************************************
'* FOR STREAM LOCKED ROM 102S REVISION 10b. *
'* USES ONLY NDRS Flash *
'* Modified by Smart_toys for use with On WHITE Nexus *
'* with 4619 Chips. OHMS not to exceed 190 *
'************************************************* *************************************
Option Explicit
Dim Shell
Set Shell = CreateObject("WScript.Shell")
Dim StartDate
Dim FileName
Dim OutFile
Dim BuffFlg
Dim bytes2
Dim GltParm
Dim ParLen
Dim ReslFlg
Dim LoopCntr
Dim RstFlg
Dim DlType
Dim Rs2Flg
Dim DlFlg
Dim bytes
Dim Uflg
Dim Acnt
Dim Mix
Dim VS1
Dim VT1
Dim DS1
Dim LP1
Dim LP2
Dim T1
Dim T2
Dim T3
Dim T4
Dim T5
Dim T6
Dim T7
Dim T8
Dim VG
Dim DD
Dim RT
Dim GT
LP1 = 1
BuffFlg = 0
LoopCntr = 0
GltParm = 176
ReslFlg = 0
Rs2Flg = 0
ParLen = 2
RstFlg = 1
DlType = 64
DlFlg = 0
Uflg = 0
VT1 = 1
DS1 = &h140B
DD = &h1453
GT= 7
RT = DS1 'Do not change any values above this line
'^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ ^^^^^^^^^^^^^^^^^^^^^^^

Sub Main()
Setupunlocker()
If CheckChipVer <> 1 then
Sc.MsgBox("Flash Version NDRS needed to run this script" & VbCr & "Flash your Loader with NewDRS.hex")
Exit Sub
End if
' These, AND ONLY THESE :), are the variables you can change for rom 102 any revision up to 108/244
LP1 = 16 'Number of tries per delay FROM 20-100 in multiples of 20
VS1 = 16 'YOU CAN CHANGE THIS FROM 02-255 = semi-automatic VCC range - Loader dependent
Mix = .0625 'Glitch VCC resolution - attempts per VCC = 1/mix
'^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ ^^^^^^^^^^^^^^^^^^^^^^
VG = VS1
sc.verbose = 0
Sc.Write("A0") ' turn led off
Clearoutputwindow
If ChkCard() = 0 then
Sc.MsgBox(" Unsupported Rom Version: Rom " & T1 & ", Rev " & T4 & " found." & VbCr & "This Script is for use with Rom 102, Rev 109/244 and higher")
exit sub
End If
If T7 = 1 then
Sc.MsgBox("Card not present or is unresponsive." & VBCr & " Unable to continue.")
Exit Sub
End If
sc.verbose = 0
Sc.Write("06 0E 03 01 03 9A 00") 'reset card
sc.read(02)
bytes = sc.getbyte(1)
sc.read(bytes)
sc.delay(16)
Sc.write("2A 6023 210020A0CA00001A041801018600AA9D9D9D9D9D9D9D9D9DAE 69CC7A9BBE000000000088 0E108500")
Sc.Read(2)
bytes = sc.getbyte(1)
If bytes > 5 then
sc.read(bytes)
bytes = sc.getbyte(0)
bytes2 = sc.getbyte(3)
If bytes = 18 and bytes2 = 132 then
Sc.MsgBox("Revision 105/241 or higher code not active on the card." & VbCr & " Card may be open or revision masked." & VBCr & " Unable to continue.")
exit sub
End if
End If
StartDate = Now()
Print "Initial Parameters = Delay:" & HexString(RT, 4) & " VCC:" & HexString(VG, 2) & " Glitch Type:" & HexString(GltParm, 2) & "/" & HexString(GT, 2)& vbcr & vbcr
Do
'sc.verbose = 1
Sc.Write(HexString(GltParm, 2) & HexString(VG, ParLen))
Acnt = 0
If RstFlg = 1 then
Do
Sc.Write("06 0E 03 01 03 9A 00") 'reset card
Sc.Read(02)
Bytes = Sc.Getbyte(1)
If Bytes > 25 then
Sc.Read(27)
RstFlg = 0
Exit Do
End if
Acnt = Acnt + 1
If Acnt > 5 then
Sc.MsgBox(" Check Loader Settings. Invalid or no atr. Card may be looped.")
exit sub
End If
Loop
'Sc.verbose = 1
Sc.write("09 6004 21C1018869 84 00")
Sc.Read(2)
bytes = sc.getbyte(1)
sc.read(bytes)
Sc.Write("14 600C 214009A0CA0000032201010E2D 0E15 5005 00")
sc.read(2)
Bytes = Sc.Getbyte(1)
Sc.Read(Bytes)
Bytes = Sc.Getbyte(3)
If Bytes <> &hA2 And Bytes <> &h6F Then
Sc.MsgBox(" Improper Cmd22 response. Unable to continue.")
Exit Sub
End If
Sc.Delay(40)
End If
If RstFlg = 0 then
'sc.verbose = 1 'debug the packets
Sc.Write("37 702C 8D00A7A000000000000000000000AA000505007AC400807180 9CA64BB76B1864CD7C1631768008AE55CC7A9B3C" & HexString(DlType,2) & HexString(RT,4) & HexString(GT,2) & "0E20 85 00")
Sc.read(2)
bytes = sc.getbyte(1)
If bytes > 5 then
sc.read(bytes)
bytes = sc.getbyte(0)
bytes2 = sc.getbyte(3)
If bytes = &hD8 and bytes2 = &h55 then
Sc.verbose = 1
UFlg = 1
End If
If bytes = &hD8 and bytes2 = &h6F then
Print "-"
VG = VG - mix
RstFlg = 0
Rs2Flg = 0
Else
Print HexString(GT,2) & "+" & HexString(bytes2,2)
RstFlg = 1
Rs2Flg = Rs2Flg + 1
VG = VG + mix
End If
Else
PRINT HexString(GT, 2) & "Rst" & HexString(VG, 2)
RstFlg = 1
Rs2Flg = Rs2Flg + 1
VG = VG + mix
End if
If Uflg = 1 then
Print " !!!!!!!" & VBCr
Sc.Write("A1")
Shell.Run "%comspec% /c echo " & Chr(07) & Chr(07) & Chr(07) & Chr(07) & Chr(07), 0, True
Sc.delay(500)
print
print "******* Good response received! *********"& VbCr
PRINT " " & HEXSTRING(bytes2,2) & VbCr
Sc.Print "===========================================" & VbCr
print " " & HexString(bytes2, 2) & " was hit at: Delay:" & HexString(RT, 4) & " VCC:" & HexString(VG, 2) & " GlitchType:" & HexString(GltParm, 2) & "/" & HexString(GT, 2) &VBCr
print " Elapsed: " & TimeDiff(StartDate,Now())& vbcr
Print " VCC Resolution: " & mix & vbcr
Print " Delay Range: " & HexString(DS1, 4) & " to " & HexString(DD, 4) & VBCr
print
PRINT "********************************" & VBCR
PRINT "* REV 109+/247+ CAM NOW OPEN!! *" & VBCR
PRINT "* PROCEED AS NORMAL *" & VBCR
PRINT "* GOOD LUCK! :-) *" & VBCR
PRINT "********************************" & VBCR
exit sub
End If
If VG < VT1 then
VG = VS1
End If
LP2 = LP2 + 1
If LP2 > LP1 / mix then '
ClearOutputWindow
RT = RT + 1
IF RT = &h1421 Then
RT = &h1443
End If
LP2 = 0
print
print "" &vbcr
print "Ram Intercept Installed. Trying to Open the 102.... Delay:" & HexString(RT, 4) & " VCC:" & HexString(VG, 2) & " Glitch Type:" & HexString(GltParm, 2) & "/" & HexString(GT, 2) & VBCr & vbcr
sc.print "Elapsed = " & TimeDiff(StartDate,Now())& vbcr & vbcr
If RT > DD then
RT = DS1 - 1
GltParm = GltParm + 5
If GltParm > 186 Then
GltParm = 176
End If
If GltParm = 181 Then
If ReslFlg = 0 Then
ReslFlg = 1
LP1 = LP1 * 2
VS1 = VS1 * 2
VT1 = VT1 * 2
ParLen = 4
End If
End If
If GltParm <> 181 Then
If ReslFlg = 1 Then
ReslFlg = 0
LP1 = LP1 / 2
VS1 = VS1 / 2
VT1 = VT1 / 2
ParLen = 2
End If
End If
End If
End If
If VS1 >= 254 then
exit sub
End If
If DlType = &h40 Then
DlType = &h20
Else
DlType = &h40
End If
If VG =< 1 then
VG = VS1
End if
End If
If Rs2Flg >= 3 Then
Rs2Flg = 0
VG = VS1
If VT1 > 10 Then VT1 = 10
End If
If VG < VT1 Then
VG=VS1
End If
If VG + mix <=0 Then
VG = VS1
VT1=VT1+1
END If
Loop
End Sub

Function HexString(Number,Length)
Dim RetVal
Dim CurLen
RetVal=Hex(Number)
CurLen=Len(RetVal)
If CurLen<Length Then
RetVal=String(Length-CurLen,"0") & RetVal
End If
HexString=RetVal
End Function
Function CheckChipVer()
CheckChipVer = 1
sc.write("90")
delay(80)
If sc.read(4) <> 4 then
CheckChipVer = 0
Exit Function
End if
If getbyte(0) <> &H4E then CheckChipVer = 0
If getbyte(1) <> &H44 then CheckChipVer = 0
If getbyte(2) <> &H52 then CheckChipVer = 0
If getbyte(3) <> &H53 then CheckChipVer = 0
End Function
Function TimeDiff (StartTime, EndTime)
Dim Hours, Minutes, Seconds
Seconds = DateDiff("s", StartTime, EndTime)
If Seconds > 90000 Then Seconds = 90000
If Seconds < 0 Then Seconds = 0
Minutes = Seconds / 60
Minutes = Fix(Minutes)
Seconds = Seconds - (Minutes * 60)
Hours = Minutes / 60
Hours = Fix(Hours)
Minutes = Minutes - (Hours * 60)
Seconds = CStr(Seconds)
Minutes = CStr(Minutes)
Hours = CStr(Hours)
If Len(Seconds) = 1 Then Seconds = "0" + Seconds
If Len(Minutes) = 1 Then Minutes = "0" + Minutes
If Len(Hours) = 1 Then Hours = "0" + Hours
TimeDiff = Hours & ":" & Minutes & ":" & Seconds
End Function
Function ChkCard()
sc.verbose = 0
ChkCard = 1
Print ""
Print " Checking Card's Eeprom Revision ......." & VBCr
sc.delay(2000)
ClearOutputWindow
Sc.Write("06 0E 03 01 03 9A 00") 'reset card
sc.read(02)
bytes = sc.getbyte(1)
If bytes < 27 then
T7 = 1
ClearOutputWindow
Exit Function
End If
sc.read(bytes)
sc.delay(16)
T1 = chr(sc.getbyte(16))
T2 = chr(sc.getbyte(17))
T3 = chr(sc.getbyte(18))
T4 = chr(sc.getbyte(23))
T5 = chr(sc.getbyte(24))
T6 = chr(sc.getbyte(25))
T1 = T1+T2+T3
T4 = T4+T5+T6
If asc(T4) = 0 then
T4 = "000"
End If
Print " Rom " & T1 & ", Rev " & T4 & " found." & VBCR
print
Sc.delay(1500)
T8 = mid(T4, 3,1)
Select Case T8
Case "A"
T8 = 10
Case "B"
T8 = 11
Case "C"
T8 = 12
Case "D"
T8 = 13
Case "E"
T8 = 14
Case "F"
T8 = 15
End Select
If left(T4, 2) = 24 then
If T8 < 7 then
ChkCard = 0
exit function
End If
End If
If left(T4, 2) = 10 then
If T8 < 9 then
ChkCard = 0
exit function
End If
End If
If T1 <> "102" then
ChkCard = 0
exit function
End If
End Function
Function setupunlocker()
Wx.BaudRate = 115200
Wx.ResetBaudRate = 115200
Wx.Parity = 0 ' 0 = None, 1 = Odd, 2 = Even, 3 = Mark, 4 = Space
Wx.StopBits = 0 ' 0 = 1 stop bit, 1 = 1.5 stop bits, 2 = 2 stop bits
Wx.DTRControl = 0 ' Initial state of DTR 0 = off, 1 = on
Wx.RTSControl = 1 ' Initial state of RTS 0 = off, 1 = on
Wx.ResetDelay = 100 ' In microseconds
Wx.ByteDelay = 10 ' In microseconds
Wx.RxByteTimeout = 3000 ' In milliseconds
Wx.ResetMode = 2 ' 0 = No Resets, 1 = ISO Reset (Expect a ATR), 2 = Device Reset (No ATR)
Wx.ResetLine = 1 ' 0 = Toggle RTS for Reset, 1 = Toggle DTR for Reset
Wx.ByteConvention = 1 ' 0 = Inverse, 1 = Direct
Wx.FlushEchoByte = 0 ' 0 = no flush, 1 = flush - A Phoenix interface will echo each byte transmitted.
Wx.FlushBeforeWrite = 1 ' 0 = no flush, 1 = flush - Flush the receive buffer before each write to strip off Null bytes.
Wx.IgnoreTimeouts = 1 ' 0 = Abort script on a receive timeout, 1 = Ignore all receive timeouts
Wx.ResetAfterTimeout = 0 ' 0 = Don't reset after a timeout, 1 = do a reset after a timeout - Not used if "IgnoreTimeouts=0"
Wx.LogTransactions = 0 ' 0 = Don't log transactions, 1 = log transactions
Wx.DisplayUSW = 0 ' Display USW after script complete 0 = no, 1 = yes
Wx.DisplayFuse = 0 ' Display Fuse after script complete 0 = no, 1 = yes
End function

[joesnuffy]

READ ME DO YOURSELF A FAVOR AND READ IT KNOW IT.





WHITE NEXUS WITH 4619
*******NOTES************************************** ********
THIS IS WHAT HAS UNLOCKED OVER 70% OF MY 10B CARDS OUT OF
10 I LOOPED 3 WATCH FOR THOSE 07+FF RESPONCES DONT LET IT HAPPEN TO MUCH. IF YOU KEEP GETTING THEM THEN TURN POT UP SLOWLY SO THEY GO AWAY THEN YOU SLOWLY LOWER YOUR POT TILL YOU GET A 07+FF RESPONCE NOW YOU KNOW HOW LOW TO GO--ADD .5 TO THE OHM READING THIS IS NOW YOUR LOW SETTING AND LEAVE IT THERE AS LONG AS THERE IS NO 07+FF RESPONCES. THE KEY IS IF YOUR GETTING THE 07+FF RESPONCES SLOWLY GO UP ON THE POT AND I MEAN SLOW BY .1 IF YOU HAVE A STEADY HAND I HAVE A KICKASS POT SO I CAN DO IT BUT DONT BE STUPIED AND GO UP 1.0 OHMS AT A TIME YOU WILL LOOP IT THAT WAY.
BUT IF YOU GET JUST 1 GOOD RESPONCE DONT MOVE YOUR POT JUST LET IT RUN IT TAKE AROUND 2HOURS TO UNLOCK.
************************************************** *********
FLASH = NEWDRS
Dip 4 DOWN
9volt 800ma
POT:15.5 TO 21.0 OHMS DONT GO UNDER 15.0 OHMS YOU WILL
GET TO MANY 07+FF RESONCES AND FROM MY EXPERANCE THE 07+FF WILL LEAD TO A LOOP SO JUST DONT DO IT. TO SET YOU POT USE A MULTIL MEATER SET OHMS TO 200 READING THEN SET YOUR POT JUST MAKE SHURE THAT WHEN YOU SET YOUR POT THE LOADER IT SLEF IS UNPLUGED OR HAS NO POWER
Notes:this script takes time be paient it can take 45mins
or so to get a +RST just let it run but if there 07+FF thats a bad thing move pot up then back slowly till there gone one a while is ok but none is better.
THESE ARE GOOD RESPONCES IT WILL TAKE AWHILE TO GET A GOOD
RESPONCE AND YOU MIGHT ONLY SEE 1 GOOD RESPONCE PERPAGE OF RUNNING SO IF YOU WATCH THE SCREEN AND YOU DONT SEE ANY GOOD RESPONCES WAIT AND WATCH CLOSELY THEY WILL POP UP. I ONCE WAITED FOR 45MINS TO GET A GOOD RESPONCE BUT IF YOU GET JUST 1 GOOD RESPONCE DONT MOVE YOUR POT JUST LET IT RUN IT TAKE AROUND 2HOURS TO UNLOCK.
**GOOD RESPONCES FROM MY WHITE NEXUS UNLOCKER**************
THIS IS THE FRIST GOOD RESPONCE AFTER 40+MINS OF RUNNING
07Rst02-------07+80---------07Rst107Rst05----
THEN THESE CAME LATER BUT NOT IN A ROW THIS IS 1 GOOD
RESPONCE PER SCREEN SO THERE WHERE LOTS OF-----07RST02--- GOING ACRRSS THE SCRREN.
07+4A
07+52
07+A0
HOPE THIS HELPS SMART_TOYS
Elapsed = 01:14:34
--------------------------------07Rst03---------07Rst02----------07Rst02-----------------------------------07Rst0E---------------------------------07Rst0C----------07Rst0C-----07+55 !!!!!!!
TX Data : A1
******* Good response received! *********
55
===========================================
55 was hit at: Delay:140F VCC:0C GlitchType:BA/07
Elapsed: 01:14:50
VCC Resolution: 0.0625
Delay Range: 140B to 1453
********************************
* REV 109+/247+ CAM NOW OPEN!! *
* PROCEED AS NORMAL *
* GOOD LUCK! :-) *
********************************

[dishdude666]

Joe,

The 10b card fortunately is not costing me a dime. It is being sent to me by a brother that just recently dropped Charlie and pick up Dave. The T911 is not modded. I honestly don’t know what chip set it has but I attached a pic wondering if you could identify. I owned a Mik II while back at the start of N2 and did the modification my self but was disappointed with my results as I had no solid support. So got rid of it and went back to the 128. Now I am running on 256 from Mili and would like to get back to the 102 area to watch TV.
So I appreciate every bit of your help and thank you for your quick reply.

PS: If I wanted to buy a 102 card what revs are recommended?

[joesnuffy]

I can't see the writing on the chips. Its easy to tell though. Look at the last 4 on the chips look for a 4053 then look for a 4911 . Why don't you send me a pm I would be glad to help you. The loader will need modding if you were going to use it. Hell I modded my loader even though it came that way with awesome pots and a power source thats one of a kind. Most likely 4053s since it isn't modded.

I recomment running emu with a real card and maxmel device thats what I am running. The computer protects the card it could be comprimised but not as easily as a bad blocker.


Joe

[birdman24]

i keep getting this when trying to run script!!


Initial Parameters = Delay:140B VCC:10 Glitch Type:B0/07

------------------------------

Sc.Read: Timeout Reading Data From Card - 2 Bytes Requested, 0 Bytes Read, Continuing Script

Script Error on Line 191
Sc.GetByte: Requested Byte Exceeds Last Read Request