ST19XL reset.

[bonecrusher]

I have mili's max/mel board.
Newer ST19 files constantly reset.
I've done some reading and it seems I need the reset mod? Can anyone help me on this one? What exactly do I mod?
Older version (2.6.05 I think) runs fine, but no premiums of course...black.
I've read over easy has or had the same problem...did you ever get it going?
Thanks in advance.

[mannybeef]

is the maxmel flashed correctly ?

[pecker88]

I have mili's max/mel board.
Newer ST19 files constantly reset.
I've done some reading and it seems I need the reset mod? Can anyone help me on this one? What exactly do I mod?
Older version (2.6.05 I think) runs fine, but no premiums of course...black.
I've read over easy has or had the same problem...did you ever get it going?
Thanks in advance.

from what i've read, mili's board HAS the reset mod. IF you are using a 2700/3900/4700/4900/301 ird, you DO NOT NEED the reset mod. Thus, cut pin1 on the db9 that hooks to the computer and you should be able to run the newest version of st19 2.6.06 with no weird resets.

IF you are running a 501/508/510/322/522/625 ird, then YOU NEED the reset mod otherwise you will have to manually restart st19 and reboot the ird every morning. Their is NO way around this other then to have the reset mod on your emu board, however the newest st19 2.6.06 does not work correctly with reset mod, thus you are somewhat screwed.

Have read that if reset mod is disabled during bootup on 501/508/510/322/522/625 ird's you can enable it after st19 is running and its fine. Thus, eliminating the need to manually reboot/reset in the morning.

hope this helps.

[mannybeef]

thank you 88

[technobro]

I try the new st today, and got some reset too

I just put a new r102 bin renamed at .... ST19.COR. work A1

[bonecrusher]

P88...
Did what you said with pin 1 on DB9...perfection, bro.
301.13 running for now with newest ST19.
Thanks alot guys for takin the time to help out...
Overeasy, I've read your posts and this sounds like the solution for you too, dude.
Test on.

[pecker88]

P88...
Did what you said with pin 1 on DB9...perfection, bro.
301.13 running for now with newest ST19.
Thanks alot guys for takin the time to help out...
Overeasy, I've read your posts and this sounds like the solution for you too, dude.
Test on.

good deal, glad u got it going!!

[chevy67ss]

from what i've read, mili's board HAS the reset mod. IF you are using a 2700/3900/4700/4900/301 ird, you DO NOT NEED the reset mod. Thus, cut pin1 on the db9 that hooks to the computer and you should be able to run the newest version of st19 2.6.06 with no weird resets.

IF you are running a 501/508/510/322/522/625 ird, then YOU NEED the reset mod otherwise you will have to manually restart st19 and reboot the ird every morning. Their is NO way around this other then to have the reset mod on your emu board, however the newest st19 2.6.06 does not work correctly with reset mod, thus you are somewhat screwed.

Have read that if reset mod is disabled during bootup on 501/508/510/322/522/625 ird's you can enable it after st19 is running and its fine. Thus, eliminating the need to manually reboot/reset in the morning.

hope this helps.

Witch category does the 6000 fall into ??

[ruciz]

6000 needs a reset mod. Basically if it can work with a MaxMel and its not a legacy IRD (2700/3100/3900/4700/4900) it needs a reset mod.

Heres an idea for those having problems that got 2 feet of 22AWG or equivilant and a SPST switch.

What you need:
Schematic on where to install reset mod (or trace its on)
wire
solder
possible x-acto knife to cut trace if its prefabbed
drill
SPST switch
1 hr of your dedicated time

remove your IRD mainboard from the shell.
drill a hole for the switch to mount in.
Mount the switch.
Install the IRD mainboard again.
If its a prefab cut the already laid RESET mod trace. You can scratch the overcoat off the board and use one side as A and one side as B.
If its not a prefab, locate the points where you need to install the reset mod. Label them A and B for now.
Run the A side to the switch center pole.
Run the B side to either side of the switch (not both!)

Now you can flip the switch, and have no reset mod. Boot IRD and get ST19 going. Once ST19 is running, flip it again to enable the reset mod and everything should be fine - least in accordance to the info posted above.

Simple.

[jarmster]

I get resets too. Auxshare 1.4 and the newest st19xl on a subbed image BUT only on the lower channels. 300 up are good but lower channels reset. Sometimes a lower ones come in but it takes a second. Its weird.

[OverEasy]

P88...
Did what you said with pin 1 on DB9...perfection, bro.
301.13 running for now with newest ST19.
Thanks alot guys for takin the time to help out...
Overeasy, I've read your posts and this sounds like the solution for you too, dude.
Test on.

Great to hear bc now did you cut the trace or suck the solder from pin1 ? The reason I haven't try it is because I've been looking at all the emu schematics on this site and none are wired up like Mili's. I didn't want to break something that wasn't broke.

[pecker88]

6000 needs a reset mod. Basically if it can work with a MaxMel and its not a legacy IRD (2700/3100/3900/4700/4900) it needs a reset mod.

Heres an idea for those having problems that got 2 feet of 22AWG or equivilant and a SPST switch.

What you need:
Schematic on where to install reset mod (or trace its on)
wire
solder
possible x-acto knife to cut trace if its prefabbed
drill
SPST switch
1 hr of your dedicated time

remove your IRD mainboard from the shell.
drill a hole for the switch to mount in.
Mount the switch.
Install the IRD mainboard again.
If its a prefab cut the already laid RESET mod trace. You can scratch the overcoat off the board and use one side as A and one side as B.
If its not a prefab, locate the points where you need to install the reset mod. Label them A and B for now.
Run the A side to the switch center pole.
Run the B side to either side of the switch (not both!)

Now you can flip the switch, and have no reset mod. Boot IRD and get ST19 going. Once ST19 is running, flip it again to enable the reset mod and everything should be fine - least in accordance to the info posted above.

Simple.

Just did what u described and what I mentioned above. Installed a micro toggel switch on the reset line. Off during bootup and version 2.6.06 works great. Then once it was running I flipped the switch and it is still running great.

In the morning, will see if it still works, but...have confirmed someone at a diff. site that tried this same exact thing and after a few days on a 625 he had to manually reset the ird...bummer.

Oh yeah, doing this all on a 522 with external 2-chip max/mel from satemu.

[bonecrusher]

Great to hear bc now did you cut the trace or suck the solder from pin1 ? The reason I haven't try it is because I've been looking at all the emu schematics on this site and none are wired up like Mili's. I didn't want to break something that wasn't broke.


I have a db9 extension cable from my pc to mili's max/mel...I just broke pin 1 off of the extension...that easy...no solder, didn't touch the max/mel whatsoever, bro...works great...now I can get on with my life...lol
Thanks again P88 !

[lelik]

Just curios what has changed between previous versions of ST19xl (before 2.6.05) and current versions for Windows, thus making “reset” problem for PVR receivers? And why it was always a problem for all Linux versions? Source code is different between Linux and Windows? When I say different , I mean program logic not actually different C language flavor.

[pecker88]

Just curios what has changed between previous versions of ST19xl (before 2.6.05) and current versions for Windows, thus making “reset” problem for PVR receivers? And why it was always a problem for all Linux versions? Source code is different between Linux and Windows? When I say different , I mean program logic not actually different C language flavor.

don't know, only PGM could answer that one. I'm sure he's trying to figure out the same thing!!!

[JT]

A reset safe version, if you want to call it that, has been released. I haven't tried it because I never had a problem with the resets. File is called st19xl-2.6.06_reset

[pecker88]

A reset safe version, if you want to call it that, has been released. I haven't tried it because I never had a problem with the resets. File is called st19xl-2.6.06_reset

That is NOT a new release from PGM. Same exact files as 2.6.06, look at the date modified on the .exe if ya don't believe me.

doesn't fix reset issue anyway.

[cancom]

That is NOT a new release from PGM. Same exact files as 2.6.06, look at the date modified on the .exe if ya don't believe me.

doesn't fix reset issue anyway.

Hi there pecker88!

Yup, same date and same problem.

I've completed my SMT2008 testing.
I've incorporated a reset mod with jumper into this latest internal maxmel version.
SMT2008 is a bit larger pc board but still the smallest footprint of any maxmel.
It also still defeats all anti-AVR tech [no special docs for each receiver].


Good to see you on top of things too JT.

Keep well
cancom