Rom10B unlock error

[duff]

I was trying to use rebelsurf's 109_247 unlocking script. I had let it run for a LOOOOONG time and it never popped. I eventually just left it going for a few days and when I came back, I had an error. I cannot remember exactly what it said but thought it might have popped.



Now when I run the script I get the following error:
Rom 102, Rev 10B found.
Initial Parameters = Delay:13A0 VCC:10 Glitch Type:B0/07

Script Error on Line 141
Sc.GetByte: Requested Byte Exceeds Last Read Request


I think it is a Cmd22 response error.



When trying to read in NagraEdit52 I get:
Opening COM1.
ATR String: 3F FF 95 00 FF 91 81 71 FF 47 00 44 4E 41 53 50
31 30 32 20 52 65 76 31 30 42 15
ROM ID: DNASP102 (ROM102)
REV ID: Rev10B
IFS has been set.
Could not test for backdoor.
Failure reading card.
Closing COM1.



As you can see I get a valid ATR. Is this a RAM loop?

Anybody got any ideas?

[TheDuke]

did you try running it through the unlocker again. It's still locked, but I've had that, script error after a long period.

[duff]

Duke, Yeah I've tried running it through the unlocker again. It just gives that error I posted immediately....doesnt even try to run which is why I thought I screwed something up on the card. I had been glitching the hell out of this thing and it just wouldnt pop and still has valid ATR so who knows.

DVD, what script would you recommend. I don't know of any besides rebelsurf that is designed to work with rev10B cams. As for the POT, I really don't know what to do there because I have an unmodded orange nexus and don't know that it can be changed without modification.

Suggestions?

BTW, thanks for the help guys...I've been gone for a week which is why I'm just now checking back in!

[SEARCHY4]

WHEN i get that error re flash your atmel again.it should clear out the error.

[duff]

Search, I have tried reflashing several times...doesnt help. I have tried flashing with dip6 only, dips1 and 6. Seems to flash ok but still get the error.
BTW, I know I'm flashing correctly because I went back to newd13 and back to newdRS again. What makes me think it's the card is that I ran the OmniUnlocker (newd13) script and it gave an error also. What's going on?



Script Error on Line 401
Type mismatch: 'T4'




which on the script is:
If Dtpnt = 165 and T4 >= 284 then
ChkCard = 0

[joesnuffy]

I see your running a non-moddedl loader their is most likely 99 percent of your problem. You got slow chips in their most likely 4053s not 4619s not to mention no jumpers on the board in loader and no pot to adjust. Send it to someone that opens cards 10bs aren't easy I thank dvd does them I can also. You may have f'd it up a tad but it still might open.

Where did you get the card? meaning do you know it is 10b stream locked or did is it possible someone put a blocker on it incorrectly. I had one like that I could force write it but then it would still show 10b when I would stick it in receiver it was still married and I know it shouldn't be after writing a totally different cam to it. I got the card from someone that f'd me but you might try using rebelserf for a rev 105 it might pop it. I never could get into that one I could have sold it and f'd someone else but thats not my style I just glitched it till it locked up.

Also try running that test script to see if interceptor is on card it was on my 10b.

I know you have unplugged and re-plugged power to the loader also try rebooting the computer and plugging and unpluggin the db9 for the loader.

Joe