Plz. help unlock ROM102 Rev10B

[blue_cobra777]

I am trying to help a friend unlock rom102 rev10b card. I have a white nexus 4719 unlocker which I bought from mili's store. My success rate is 50% one out of two. I have unlocked a rev103 over a year ago and looped a rev105. Can someone point me to right script and instructions.
Also please can someone shed some light on what is (no looping, diode mode) unlocking?

Thanks a lot.

[SEARCHY4]

i have the diode mod and stll looped 10 10b cards. only 1 popped.
you looped a 105? wow . pooped more then i can count of those.also using white nexes. try the reb surf 109+ but dont be mad when that sucker loops.

[skinerd]

Some 10Bs will pop some won't.......they are tough, looping is a real possibility.

[HILLBILLY]

i have the diode mod and stll looped 10 10b cards. only 1 popped.
you looped a 105? wow . pooped more then i can count of those.also using white nexes. try the reb surf 109+ but dont be mad when that sucker loops.
use orange nexus, with new chip set and diode mod, using the 109+ script and dips 2/5 down, 300ohms on the pot. seems most the posts read about blue, orange or white nexus, the 300ohms is good.
good luck
HB

[blue_cobra777]

Thank you all for your expert opinions. Since I dont have an orange nexus, I guess I cant use the diode mode. Anyways.. I dont even know what it does... BUT

I have two questions.

When you say 300 Ohms? I am not sure what that means. Coz. when I test the ohms on my white Nexus POT using a meter, the meter reads 2.65 and I can move it up and bring it to 3.07 and it goes max to about 4.xx something... Is 3.00 same as 300 OHms your are refering to? I am confused......


Changing Delay from 140b to 140a? Which script should I use? Can someone point me to the right script for Rev10B stream locked?

Thanks very much......

[HILLBILLY]

Thank you all for your expert opinions. Since I dont have an orange nexus, I guess I cant use the diode mode. Anyways.. I dont even know what it does... BUT

I have two questions.

When you say 300 Ohms? I am not sure what that means. Coz. when I test the ohms on my white Nexus POT using a meter, the meter reads 2.65 and I can move it up and bring it to 3.07 and it goes max to about 4.xx something... Is 3.00 same as 300 OHms your are refering to? I am confused......


Changing Delay from 140b to 140a? Which script should I use? Can someone point me to the right script for Rev10B stream locked?

Thanks very much......
i should have said i use an orange.....i figure all the nexus' are similar anyway. the diode mod can be done on your nexus, but not sure it'll help with the 10b anyway, so don't worry about that. 300 when your dial is set at 2000.....it would be .30 if set at 20k....3.07 is way too high. don't worry about the script if u are new at this.....be warned, there is a good chance u will loop this card.
HB

[SEARCHY4]

MINES AROUND THE 220 OHMS. tryed all other spots.thats my sweet spot your will be differant.even though same unlocker each one has it's own sweet spot.practice on a old rom 10 if you got one. the old scripts cam with vcc annalizer wich was real handy on finding sweet spots.for some reason they dont no more.one you get to know your loader you will now when you see a good set of 7f7f7f rst rst.
to many 7f7f7f7f7f7f7 or rst rst rst rst.
ours will look ----------------- rst12 ----------------------------------------------------------
if to many -------- turn up a hair
you can also practice with a unlocked card it helps

[Wiley-X]

This is off-topic, but it bothers me....

I don't think it's respectful that Mili and the mods allow this person to use the Nick of Hillbilly. No offense to you personally, but Hillbilly was a very respected tester out at DSSROOKIE who has since passed on and I think his nick should be reserved.

~Wiley~

[SEARCHY4]

another off topic.
wiley i think i remember you from the old kicken chicken days.
glad to see your still around.keep up the great help.

[HILLBILLY]

This is off-topic, but it bothers me....

I don't think it's respectful that Mili and the mods allow this person to use the Nick of Hillbilly. No offense to you personally, but Hillbilly was a very respected tester out at DSSROOKIE who has since passed on and I think his nick should be reserved.

~Wiley~
u really shouldn't decide or say shit. i signed up july 2004. 3.5 years ago. 2 years and about 900 posts before you. was he passed when i joined? nope!! fuck you. i paid my respects when he passed. he even pm'ed me and said "nice nick" when i chose it. i believe he was here as hillbilly1. nothing personal, but this isn't DSSROOKIE. so i should change the nick i've had for 3.5 years and pretend the world stopped turning because it bothers you? should i change it at 10x and DJ too? FUCK OFF!!!!
I am hillbilly, i will stay hillbilly.

[rg6a]

u really shouldn't decide or say shit. i signed up july 2004. 3.5 years ago. 2 years and about 900 posts before you. was he passed when i joined? nope!! fuck you. i paid my respects when he passed. he even pm'ed me and said "nice nick" when i chose it. i believe he was here as hillbilly1. nothing personal, but this isn't DSSROOKIE. so i should change the nick i've had for 3.5 years and pretend the world stopped turning because it bothers you? should i change it at 10x and DJ too? FUCK OFF!!!!
I am hillbilly, i will stay hillbilly.

I'd hazard a guess that you guys won't be doing lunch in the near future.


P.S. seriously though, he was respectful and you really <F>lamed. He should
of PM'd Mili, but he didn't and your response should of been via PM also,
I'd call it a wash, and both walk away and forget it!

[HILLBILLY]

I'd hazard a guess that you guys won't be doing lunch in the near future.


P.S. seriously though, he was respectful and you really <F>lamed. He should
of PM'd Mili, but he didn't and your response should of been via PM also,
I'd call it a wash, and both walk away and forget it!
respectful? saying i shouldn't have my nick anymore because someone on another site passed away? come on, should have minded his own business. some people don't remember some of the contraversy around other hb(RIP), and his dad(rip). i took alot with that going down, bieng confued with him. even had death threats.(i won't bring things back up, older testers remember, and let the man rest, i did also respect him) if peeps just minded thier own, things would be peaceful. i am just defending myself.
hb

[killer_1]

these 10b's are like having sex slow and easy. I haven't loop any 10b's using old orange nexus with 4053 chip using rebel's mod script for 4053 orange nexus.
190-198 omhs switch 1

killer_1

[J5063]

I am trying to help a friend unlock rom102 rev10b card. I have a white nexus 4719 unlocker which I bought from mili's store. My success rate is 50% one out of two. I have unlocked a rev103 over a year ago and looped a rev105. Can someone point me to right script and instructions.
Also please can someone shed some light on what is (no looping, diode mode) unlocking?

Thanks a lot.
WAS LOOKING AT YOUR POST THIS MORRING AND I HAD 2 CARD`S
102REV AT 10B ABOUT 4 OR 5 YEARS AGO AND A 301-10 UNPLUG BACK THEN
AND I TRY THEM ABOUT 2 AM TODAY AND THAY WERE DEAD SO I TRY TO GET THEM TO WORK SO I TRY THAT REBEL-SERF ABOUT 8 OR 10 TIME`S
AND BINGO OPEN AND WORKING JUST FINE. THANK YOU
I BEEN ON COOLSAT FOR THE LAST 5 OR 6 YEAR`S AND THAT WHY IT WAS
UNPLUG WAS THINKING MAYBE OF GETING IT WORKING BUT I DON`T NO WHAT I HAVE TO DO FOR THAT BEEN OUT OF THIS A LONG TIME

[HILLBILLY]

MINES AROUND THE 220 OHMS. tryed all other spots.thats my sweet spot your will be differant.even though same unlocker each one has it's own sweet spot.practice on a old rom 10 if you got one. the old scripts cam with vcc annalizer wich was real handy on finding sweet spots.for some reason they dont no more.one you get to know your loader you will now when you see a good set of 7f7f7f rst rst.
to many 7f7f7f7f7f7f7 or rst rst rst rst.
ours will look ----------------- rst12 ----------------------------------------------------------
if to many -------- turn up a hair
you can also practice with a unlocked card it helps
search is right, each one does have a sweet spot. mine for 108 or under is 215, i looped 2 10b's at that ohm's, so i read a sht load of threads and seemed that 300 was the way to go for 10b. tried it and havn't looped one since.

[Benleo1]

I've heard of a few private scripts for the 10b , but don't have access to them. A 50% loop rate is about average for what's publically available.