skinerd
04-24-2008, 10:58 AM
Swiped this from another site......it is GOOD info.
************************************************** **************
I've made this post because as I look through these forums I can not believe there are people that are putting these couple hundred dollar cards in there unlockers and not knowing what the Dip switch settings are used for. I have a Nexus and have spent a few minutes tracing the lines for the Dip settings.
OK, first I would like to clear up is on these Orange, Blue, Clear Nexus's. You do not have to have pin 1 & 6 down to be able to flash. I don't know who came up with that but they don't know what there talking about. The only pin you need down to flash on these Nexus's is Pin 6. Pin 1 is a clock line and it doesn't hurt to have it down while flashing but I'm sure it doesn't help neither and could be a reason why so many people are having problems flashing there loaders.
Remember that only one clock pin can be down at one time or you can damage your loader.
Pins 1-4 are your clock pins on the Nexus Orange/Blue/White/Cyclone. I will say it again so that we can stop this miss information about flashing nexus's. You DON NOT need to have Pin 1 down to flash your loader, only Pin6 needs to be down. I've trace all pin outs on the Nexus and Pin1 has nothing to do with flashing, it is a glitch clock line.
Orange/Blue/White/Nexus & Cyclone
Pin1 - 9.216mhz/Inverted (-CLK/2)
Pin2 - 18.432mhz/Non Inverted (+CLK) *Used most often for glitching*
Pin3 - 18.432mhz/Inverted (-CLK)
Pin4 - 9.216mhz/Non Inverted (+CLK/2)
Pin5 - Grounds pin16 of Atmel/Disabled *Use with pin 2 for glitching*
Pin6 - Flash enable pin *This pin is the only one to be on while flashing*
Powersync
Pin1 - 18.432mhz/Inverted (-CLK)
Pin2 - 18.432mhz/Non Inverted (+CLK) *Used most often for glitching*
Pin3 - 9.216mhz/Inverted (-CLK/2)
Pin4 - 9.216mhz/Non Inverted (+CLK/2)
Pin5 - Flash enable pin *To be used for flashing Atmel*
T-911, Detonator XP, T6 Wave or Detonator II/ III
Pin1 - Flash enable pin *To be used for flashing Atmel*
Pin2 - Grounds pin16 of Atmel/Disabled *Use with pin 5 for glitching*
Pin3 - 9.216mhz/Inverted (-CLK/2)
Pin4 - 9.216mhz/Non Inverted (+CLK/2)
Pin5 - 18.432mhz/Non Inverted (+CLK) *Used most often for glitching*
Pin6 - 18.432mhz/Inverted (-CLK)
************************************************** **************
I've made this post because as I look through these forums I can not believe there are people that are putting these couple hundred dollar cards in there unlockers and not knowing what the Dip switch settings are used for. I have a Nexus and have spent a few minutes tracing the lines for the Dip settings.
OK, first I would like to clear up is on these Orange, Blue, Clear Nexus's. You do not have to have pin 1 & 6 down to be able to flash. I don't know who came up with that but they don't know what there talking about. The only pin you need down to flash on these Nexus's is Pin 6. Pin 1 is a clock line and it doesn't hurt to have it down while flashing but I'm sure it doesn't help neither and could be a reason why so many people are having problems flashing there loaders.
Remember that only one clock pin can be down at one time or you can damage your loader.
Pins 1-4 are your clock pins on the Nexus Orange/Blue/White/Cyclone. I will say it again so that we can stop this miss information about flashing nexus's. You DON NOT need to have Pin 1 down to flash your loader, only Pin6 needs to be down. I've trace all pin outs on the Nexus and Pin1 has nothing to do with flashing, it is a glitch clock line.
Orange/Blue/White/Nexus & Cyclone
Pin1 - 9.216mhz/Inverted (-CLK/2)
Pin2 - 18.432mhz/Non Inverted (+CLK) *Used most often for glitching*
Pin3 - 18.432mhz/Inverted (-CLK)
Pin4 - 9.216mhz/Non Inverted (+CLK/2)
Pin5 - Grounds pin16 of Atmel/Disabled *Use with pin 2 for glitching*
Pin6 - Flash enable pin *This pin is the only one to be on while flashing*
Powersync
Pin1 - 18.432mhz/Inverted (-CLK)
Pin2 - 18.432mhz/Non Inverted (+CLK) *Used most often for glitching*
Pin3 - 9.216mhz/Inverted (-CLK/2)
Pin4 - 9.216mhz/Non Inverted (+CLK/2)
Pin5 - Flash enable pin *To be used for flashing Atmel*
T-911, Detonator XP, T6 Wave or Detonator II/ III
Pin1 - Flash enable pin *To be used for flashing Atmel*
Pin2 - Grounds pin16 of Atmel/Disabled *Use with pin 5 for glitching*
Pin3 - 9.216mhz/Inverted (-CLK/2)
Pin4 - 9.216mhz/Non Inverted (+CLK/2)
Pin5 - 18.432mhz/Non Inverted (+CLK) *Used most often for glitching*
Pin6 - 18.432mhz/Inverted (-CLK)