I followed the instructions for the no zkt mod for the 430/431 mod exactly.

I got all the way to the last step and I get an error.
The error reads Error detecing erasing sector.

I get at the bottom of the window awaitng erasure completion. sector 1
sector 2

all the way to 31 and then the error.

Any Ideas or solutions?



thanks

Okay, i got past the error. I just did it four time and it findly worked.

But now I'm getting another error.

Error reads Error performing flash write request.

Next, Error programming flash at offsetOxfC00000

any ideas???

has anyone every seen this error??

I believe the only thing left is to right the bin to the DRD430.

Only thing is, this is when I get the error.

I have checked my connections many, many times.

Everything looks fine.

now the green light will not come back on. no wires are contected.

damn..........

[mdeven]

HDTV MAN,
I got your message.... The reason I haven't responded before, is that I don't know what to tell you.... While I've been doing this stuff for a few years now, there is alot that I still don't know.... While I do hold degrees in electronics and computer science, that doesn't always help.... I have only done two IRD mods to date and don't consider myself qualified to answer your questions.... There is however, a very good thread going on the same subject.... That's why I'm going to have to start preaching the virtues of reading and using the search function.... Nothing personal guy.... We are getting a good message base back up and are starting to attract some good people....
Please read through the other threads....
Sorry, while I AM the chosen one, I still have alot to learn....
Mark

this is not the same topic as the other thread.

[mdeven]

I'm trying to point you towards someone who might be able to help you better than I can....
Mark

Originally posted by mdeven
I'm trying to point you towards someone who might be able to help you better than I can....
Mark

thanks,

buddy

Thanks, cedricdog


anohter question: When I start the Chip/Sector Programming I get the following:

Program at address 0x7FC0000, size 0x400000 ? I hit the yes button and it says flash is not currently blank, continue anyway...

Then it errors out.

any ideas??

I can not erase the flash it gets to sector 31 and errors. What do I need to do?

[mdeven]

Cedricdog,
Thanks man.... I owe you one....

HDTV MAN,
Told you I'd find you someone who can lend a hand....
Mark

cedricdog your the man.....

everything seems to working like a charm. Only one thing the remote now does not work any ideas?

thanks

can't seem to get to the site you posted

I have redone the process three time to the same receiver and still not remote.

Anyone have a sollution?

thx

14 hours and the remote is fine. i guess i will erase the flash and write it back and see if this helps

Originally posted by cedricdog
OK. just looked at a 430 and measured voltage at the infrared sensor. get out your meter and try this. facing the back of the receiver look at the sensor and you will see three pads. the left pad i got no voltage. i assume this is a ground. the middle pad i got 5 volts. the right pad i got slightly less than 3 volts. when i activated the remote i was able to detect a transient variation of about 0.25 volts. i did not take the circuit board out to look any further. i would try looking here first and see it you are getting the transient. this way i think you can rule out the sensor.

let me know what you find and we can go from there.

thanks will do

wile trying to fix the remote issue, I killed the IRD. That makes two I have killed.

This sux's i don't have another 430/431 left.

oh well...................

I can not get the jtag program to reconize the IRD.

Originally posted by cedricdog
dude,

if you still get power to the receiver then you haven't killed it. it's still reprogrammed. unless you've got some port left i would not try and reinstall the jtag. but that's up to you. the remote problem has nothing to do with the flash. it's something else. did you check the readings at the infrared sensor?

I have tried it three times and still nothing. I have another that I can't clean sector31.

what a bitch..

cedricdog

I want to think you for all your excellent help!

Your right I was up all night trying to get this to work. I should have taken your suggestion to slow down, take a deep breath, have a beer or a valium or both and rethink this.

I can't seem to get the 431 to do anything, all it tells me there is a short some where.

I have replaced the JTAG several time and still no success.

I got the eprom erased, but can't get the damn thing to read anymore.


HD

it's okay to follow the trace up a little further to find a better contact.

Right?

Originally posted by 001438
You can use a contact pad that is a little further up. That is what I did because the jtags are so close together.

worked great!!!